On the route · Kuna
The rest of the lineup
Same $99 diagnostic, same written quote, same written warranty on every machine we fix in Kuna.
No ice for a week. Cubes that are hollow shells. A bin that keeps freezing into one block. The ice maker is the smallest machine in a Kuna kitchen and the first one that hard water quietly kills. We drive down from West Boise, test the fill valve and the module with a meter, and write one price before any part is touched.
Mon–Fri 8am–6pm · Sat 9am–3pm · Sunday closed · same-day windows for a warm refrigerator
Same $99 diagnostic, same written quote, same written warranty on every machine we fix in Kuna.
From the shop at Five Mile Rd and Ustick Rd the drive is simple: Five Mile south, Overland west, Ten Mile Rd all the way down through the new roundabouts to Kuna, about twenty minutes without traffic. The houses at the end of that drive are mostly ten years old or newer, in subdivisions off Deer Flat Rd, Kuna Rd and Lake Hazel Rd, and nearly every refrigerator in them has an ice maker and a dispenser. Every one of those fill valves is fed by hard water, from the city wells or from a private well outside the limits, and scale is what we find in the valve more often than any other fault.
The fill valve is a small solenoid with a tiny orifice, and a few years of Kuna water narrow it until the tray fills short. Short fills give small or hollow cubes; a valve stuck partly open dribbles into the tray after the cycle and freezes into a sheet that jams the ejector. On wells with iron, the ice comes out with a faint orange tint and a metallic taste, which people mistake for a filter problem. One call near Indian Creek last spring involved a two-year-old LG making no ice at all: the valve was so scaled it passed almost no water, and the softener in the garage had been bypassed since a plumbing repair.
Water not reaching the tray, or a module that has stopped cycling. We check the fill valve on the meter and with a timed fill, look at the supply line for a frozen spot, and test the ice maker module or the optics sensor. The freezer temperature is checked too; above about 10°F many units will not cycle.
A short fill. The valve is scaled, the supply pressure is low, or the water filter has plugged. We measure the fill volume against spec, replace or clean the valve, and check the filter date. On a private well outside Kuna we also look at the house pressure at the tank before blaming the refrigerator.
Either the bin sits under a leaking valve that keeps dripping, or the freezer is cycling warm during defrost and the cubes are melting together. We check the valve seal, the defrost cycle timing and the door gasket. A block of ice once a week in summer often means the door is not sealing.
An old water filter, iron in the well, or a bin that has absorbed freezer odors. We check the filter, look at the supply line material, and clean the bin and chute. Iron staining in the ice itself is a water issue we will point out, not a part we can replace, and we say so plainly.
A cracked fill cup, a valve that seeps after it should close, a supply line fitting behind the fridge, or a frozen fill tube. We trace the water with the fridge pulled out, replace the failed part, and check the line where it comes through the wall or up from the crawlspace.
The dispenser and the ice maker share the valve body but use different solenoids, so one can fail alone. Or the module, the ejector motor or the shutoff arm has failed. We meter the ice maker solenoid and the module separately and replace only what is dead, then run a harvest to prove it.
An ice maker is diagnosed by forcing it through a cycle and watching what it does. The technician starts a test harvest, times the fill, and measures how much water actually lands in the tray against what the manufacturer specifies. The fill valve is metered for coil resistance and checked for seep after closing. The freezer temperature is logged, because a freezer running at 15°F will slow or stop most ice makers even with everything else working. The supply line is traced to the wall to look for kinks, freezing or a saddle valve that is nearly shut. Then the failed part is named in plain words and one price is written under it. On most Kuna visits that part is on the truck.
Ice makers inside Samsung, LG, Whirlpool, Frigidaire and GE refrigerators make up most of the Kuna work, with KitchenAid and Bosch in the larger homes and Sub-Zero or Thermador on a few of the acreage properties out Swan Falls Rd. Landlords with rentals near Kuna High School and along Avalon St can have the tenant let us in and approve the written number by text; the invoice and written warranty go to the owner. We repair the ice maker built into the refrigerator, not standalone ice machines. The $99 diagnostic is inside the repair price you approve, and if you stop after the diagnosis, $99 is the whole bill. Every repair figure is written after the diagnostic, not estimated on the phone.
Short fills, almost always from a fill valve narrowed by scale. Kuna water is hard enough that a valve can lose half its flow in three or four years, faster on a private well without a softener. We measure the fill, replace or clean the valve, and check the filter and supply pressure so the new valve gets a fair start.
Yes. The ice maker, its valve, the module and the fill tube are all separate, replaceable parts, and the refrigerator around them is usually fine. The written number covers only what failed. If the freezer itself is running warm and starving the ice maker, we say so and quote that repair instead.
No. We repair the ice maker and its fill valve, and we will replace the short supply line and fitting behind the refrigerator when that is the leak. New water lines through walls, softeners and whole-house filters are plumbing, and we will tell you in writing when that is the next step.
Same week and often next business day, Monday to Saturday. Ice makers ride along with refrigerator calls, so if you also have a warm fridge, say so and the visit moves to a same-day window. Tell us the refrigerator brand and whether the dispenser still gives water, which narrows the likely part.
Sometimes. A filter well past its six-month life can cut the flow enough to give small cubes, and it is the first thing we check. But a fresh filter with the same small cubes means the valve or the pressure. We do not sell filters; if yours is old we tell you and test the machine with the bypass plug.
Call (208) 813-1132 or send the form. Most requests get a callback within the hour in business time, with a real arrival window.
The technician tests the machine with a meter, names the failed part in plain words, and writes one flat price. The $99 is already inside it.
We stock the high-failure parts for the brands Treasure Valley homes actually own, so most jobs close on the spot; ordered parts return with no second trip fee.
Full test cycle before we pack up, a tidy work area after, and a written warranty in your hand.
One call starts it: $99 diagnostic, one written number, repair from the truck, written warranty.
